Facebook

WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

Custom Five-Band Signal Boosters for Distributor Projects

От greetwin November 16th, 2026 3 просмотров

Introduction: A distributor sourcing a five-band signal booster for a project order needs one RFQ that ties local band plans, connector scope, customization requirements, and shipment contents to the exact model under review.

A distributor rarely buys a cell signal booster as a standalone item. The order usually supports a building project, a small operator rollout, or a channel restock, and the details must line up before a quote is useful: which 2G/3G/4G bands local networks use, what feeder and antennas the installer plans to use, how many units the project needs in each phase, and what adjustments the target market requires. A cellular signal booster order benefits from one consolidated RFQ, because clear inputs shorten quoting and help the shipment match the site.

Why Regional Band Plans Should Drive a Distributor RFQ

Start the five-band RFQ with the target band list so the supplier can match the model to the market. Spectrum allocations differ by country and region, and ITU-R coordinates radio frequencies internationally. The Greetwin five-band model covers 800/900/1800/2100/2600MHz for 2G, 3G, and 4G, mapping to LTE800, EGSM900, 1800MHz, WCDMA2100, and LTE2600. This combination fits many networks across Europe, the Middle East, Africa, Asia, and parts of South America. The exact edges matter when an engineering contact compares them with operator data: uplink 832–862 / 880–915 / 1710–1785 / 1920–1980 / 2500–2570MHz and downlink 791–821 / 925–960 / 1805–1880 / 2110–2170 / 2620–2690MHz. Include that frequency table in the RFQ. It shows the supplier what the market uses and lets the factory flag mismatches before labeling or configuration work begins. If a target market relies on three of the five bands and reserves the other two for future capacity, state that split. If the project spans countries with different plans, list each market separately. Quantity belongs in the same section, because it drives how the order is built: a single building project might need two units plus one spare, while a distributor restocking for a region might need a mixed batch split by market. State the project phases, the split per country or site type, and whether you want one common configuration across the batch or market-specific variants. Clear phase and quantity information reduces clarification rounds and shows that the request covers a distribution program.

How Connector, Power, and Configuration Details Shape the Requested Model

Once the bands are fixed, mechanical and electrical details determine whether the units go straight into the project or wait in the warehouse for adapters. Distributors who send these details with the first inquiry receive a quote they can forward to the installer. The model uses wall installation and IP40 indoor protection, so the site plan should assume fixed indoor mounting.

1. Why the 50-Ohm N-Female Interface Must Match the Planned Feeder System

The five-band unit uses 50-ohm N-Female connectors. Matching that interface to the planned cable and antenna hardware keeps the RF path clean. A 50-ohm system joined to a mismatched connector or random adapter adds reflections, loss, and extra risk near the isolation limit. Its VSWR is ≤2.0, so the feeder and antenna work should follow the same impedance discipline. Ask the installer which cable type and jumper length the site will use, and include that information in the RFQ. If the project standard is 7/16 DIN or SMA, raise it at inquiry so jumper or adapter planning can be settled before the purchase order.

2. How Package Scope and Antenna Accessories is worth checking Before Quoting

Shipment scope changes the commercial picture. A host-only scope and a scope that includes antennas and cable lead to different quotes, logistics, and launch dates. List donor antennas, server antennas, coaxial cable, mounting hardware, and the power supply line by line, then decide what to source locally and what to ship with the units. Antenna selection follows the site plan: a rooftop donor feed and an indoor server antenna serve different roles in the coverage design. On power, the unit accepts AC 90-264V and DC 10V/10A, which covers 110V and 230V markets from one model. Confirm the packing list in writing so delivery matches the quotation to your customer.

How Factory Customization and Compliance Questions Fit a Project Order

Customization is where a distributor relationship with a source factory earns its keep. Greetwin runs a Shenzhen factory and supports end-to-end customization for specific bands and power, so a request can go beyond catalog selection. Describe the target market in engineering terms: required band edges, output power level assumed by the coverage plan, connector and packaging requirements, and quantity per variant. The model provides uplink 70dB±2dB gain with 20dBm±2dBm output, downlink 75dB±2dBm gain with 23dBm±2dBm output, ALC >20dB, and MGC 31dB in 1dB steps. Those controls also give the installer the settings they will use on site. ALC holds output in check under strong donor input, and 1dB MGC steps let an installer tune attenuation in small increments when antenna isolation is tight. Compliance questions belong in the same RFQ. Radio equipment sold into European markets falls under the Radio Equipment Directive, and electronics are covered by RoHS substance restrictions. A distributor preparing a European or export project should ask which documents are available for the exact model being quoted and confirm their status before placing the order. Price, MOQ, lead time, warranty terms, and certification document status are confirmed in the RFQ; a written answer on each point makes the offer reviewable by your management. Ask also what the shipment includes, how customization limits apply to your band request, and who handles technical questions after delivery.

Conclusion

A five-band distributor order comes together in a predictable order: band plan, quantity and project phasing, connector and power details, package scope, then customization and compliance documents. Distributors who prepare those blocks before contacting a factory receive quotes they can act on and shipments that match the site. The Shenzhen factory builds these five-band units and supports band and power customization for distributor programs. Send your target-market band list, project quantity, planned feeder and accessory scope, and customization needs in one RFQ; ask for the packing list, compliance documents, and commercial terms in the same reply.

FAQ

Q: What information should a distributor include in a five-band signal booster RFQ?

A: Include the target market's uplink and downlink band ranges, the network technologies in use, the quantity per project phase or country, the planned connector and feeder type, whether antennas and cable should ship with the units, any label or packaging requirements, and the compliance documents you need to review. Adding the site type and planned installation method helps the factory recommend the right configuration.

Q: Can a five-band repeater be customized for specific regional frequency bands?

A: Yes. Greetwin supports end-to-end customization for specific bands and power from its Shenzhen factory, so a distributor can request band edges that match a regional network plan. Describe the required uplink and downlink ranges and the output power level in the RFQ, and confirm the feasible customization scope for your quantity before the order is finalized.

Q: Are donor and server antennas included with a custom five-band booster order?

A: Confirm the antenna and cable scope in writing. The five-band unit has 50-ohm N-Female connectors and works as part of a system with a donor antenna, a server antenna, and 50-ohm feeder. Ask for a line-by-line packing list in the RFQ covering antennas, cable, mounting hardware, and the power supply so your quotation to the end customer matches the delivery.

Sources / References

ITU-R: Managing the radio-frequency spectrum for the world

Radio Equipment Directive (RED) - Internal Market, Industry, Entrepreneurship and SMEs

RoHS Directive - Environment - European Commission

Related Examples

20dBm 5 Band 2G 3G 4G Signal Booster 800 900 1800 2100 2600MHz with LCD Screen, ALC&MGC

Назад
Wall-Mounted Cell Signal Boosters for Office and Basement Floors
Читать далее
Далее
Donor and Server Antenna Distance in Indoor Repeater Installation
Читать далее